•  
    Page 1 of 5 123 ... LastLast
    Results 1 to 10 of 49

    Thread: Short Shifter Swap

    1. #1
      Lifetime owner
      Join Date
      Sep 2008
      Location
      Pittsburgh
      Posts
      8,013
      Garage empty: add car
      Thanks
      2
      Thanked 170 Times in 141 Posts

      Short Shifter Swap

      I am not going to go step buy step like open you hood, jack up car etc..

      This can be done from above, or you can go below the car to reach the shaft from shifter in the car.
      I literally did this in 5 minutes.

      Tools needed:

      2 flat heads, or a good trim tool (not the press steel kind)
      a 12mm & 14mm socket, or box. one of each.

      step 1. Locate the shifter arm, it is behind the transmission near the firewall. There is an opening between the intake manifold and master cylinder. (If i already lost you, get help).

      step 2. There is a rectangular clip on the top of the arm, with two spring clip on each end.



      Lift the spring clips, and then put a screw driver (or trim tool to be on both sides of the rivet head) under the flat part near the middle and lift it out. you may need to unclip one of the plastic ends on the arm above the shift lever for clearance.



      step 3. Follow the linkage to the transmission There is a joint where the linkage meets the input shaft. On one side of this joint is a J clip (much like a C clip but easier to take off) i lifted it with my finger and slide it off, if you need a screw driver do that. Then pull the pin out, and separate the joint (it will fall apart).



      step 4. This is the only part i did from under the car. Mark the linkage for its position (put tape around the side of the linkage you are taking off). remove the 14mm set nut and the 12mm bolt. Slide the shafts apart.



      Picture of it removed and marked (prior to removing):



      step 5. Pull out the linkage swing arm.

      should look like this:


      step 6. have a beer. (pepsi if <21).



      under 21:


      step 7. on a table or work station (including driveway). unclip the plastic ends off the arm and set it aside.

      step 8. remove the two c clips from the pivot ends on the linkage. Once the C clips are off pull the metal brackets, and then pop off the plastic cups.

      step 9. slide out the two bushings in the center pivot of the swing arm.

      step 10. Done.



      Reverse order to install.




    2. #2
      Should I keep it?
      Join Date
      Oct 2008
      Posts
      35
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts

      Re: Short Shifter Swap

      Awesome how to, I still dont know where to get the linkage from though?

    3. #3
      Almost time to do my timing belt
      Join Date
      Mar 2009
      Location
      Fairbanks, Alaska
      Posts
      1,207
      Garage empty: add car
      Thanks
      0
      Thanked 2 Times in 2 Posts

      Re: Short Shifter Swap

      I've got a technical queston. If that's a crushed coke spilt there why is the liquid red?
      Farthest North Aveo: Fairbanks, Alaska

    4. #4
      Timing belt broke, do I keep it? thehunterooo's Avatar
      Join Date
      Mar 2009
      Location
      Tampa and Orlando
      Posts
      4,359
      Garage empty: add car
      Thanks
      0
      Thanked 4 Times in 4 Posts

      Re: Short Shifter Swap

      hmm nice one wolf, i too have not witnessed red coke

    5. #5
      What's wrong with my car?
      Join Date
      Jan 2008
      Location
      Irwin, PA
      Posts
      26
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts

      Re: Short Shifter Swap

      the coke got a beating cause he was red. cant we all just get along.
      "With my last breath, I curse Zoidberg!"

    6. #6
      Timing belt broke, do I keep it? thehunterooo's Avatar
      Join Date
      Mar 2009
      Location
      Tampa and Orlando
      Posts
      4,359
      Garage empty: add car
      Thanks
      0
      Thanked 4 Times in 4 Posts

      Re: Short Shifter Swap



      how violent

    7. #7
      I'll keep it and add a turbo
      Join Date
      Oct 2008
      Location
      Tehachapi, CA
      Posts
      205
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts

      Re: Short Shifter Swap

      petrified rabbit, you have a great taste in soda and beer

    8. #8
      Timing belt broke, do I keep it? thehunterooo's Avatar
      Join Date
      Mar 2009
      Location
      Tampa and Orlando
      Posts
      4,359
      Garage empty: add car
      Thanks
      0
      Thanked 4 Times in 4 Posts

      Re: Short Shifter Swap

      he doesnt like coke i can see

    9. #9
      Timing belt broke, do I keep it? thehunterooo's Avatar
      Join Date
      Mar 2009
      Location
      Tampa and Orlando
      Posts
      4,359
      Garage empty: add car
      Thanks
      0
      Thanked 4 Times in 4 Posts

      Re: Short Shifter Swap

      how long did it take you to set that up for that picture anyways??? :P

    10. #10
      Lifetime owner
      Join Date
      Sep 2008
      Location
      Pittsburgh
      Posts
      8,013
      Garage empty: add car
      Thanks
      2
      Thanked 170 Times in 141 Posts

      Re: Short Shifter Swap

      Quote Originally Posted by thehunterooo
      how long did it take you to set that up for that picture anyways??? :P
      thats what my fridge always looks like, usually the beer would push out the pop ( or soda for yins) but then i bottle bottles.

      Now the beer gets is own shelf.


      Short shifter is in. Anyone want to go measure the throw of their stock one? (i forgot to do that)

      I measured from the bottom of the AC button against the dash to the line in the H pattern on the shift knob.

      its about 3-3 1/2" throw.. from gear to gear.






    Page 1 of 5 123 ... LastLast

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •