•  
    Page 3 of 4 FirstFirst 1234 LastLast
    Results 21 to 30 of 33

    Thread: 2010 Aveo won't start.. No codes

    1. #21
      What's wrong with my car?
      Join Date
      May 2021
      Location
      Utah
      Posts
      13
      Garage empty: add car
      Thanks
      1
      Thanked 0 Times in 0 Posts
      Ok so so maybe I'm being a little naive here but I'm hoping that maybe my head is fine, what's the likely hood of this?
      THat said, I've pulled the belt which was not completely broken but it was quite torn up and I'm quite certain the cam's were out of sync. However, I'm able to turn them with no nasty sounds or grindy/crunchy noises coming from the motor internally.
      Here's a few pics of things, a couple showing where the cam's were before I aligned them "I think" ( that's actually something else I need to verify somehow, how do I know where to have those cam's and when I'm at TDC?)
      In the one pic labled cams aligned I've also got the crank aligned with the timing mark on the crank and the block. I'd love to just slap on a new timing belt and be done with it any chance that's an option?
      Name:  Cams aligned.jpg
Views: 386
Size:  288.8 KBName:  20210508_152350.jpg
Views: 393
Size:  292.9 KBName:  20210508_152359.jpg
Views: 426
Size:  299.1 KBName:  20210508_152335.jpg
Views: 419
Size:  341.9 KB



    2. #22
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      552
      Thanks
      1
      Thanked 55 Times in 51 Posts
      Quote Originally Posted by Offroadr View Post
      Ok so so maybe I'm being a little naive here but I'm hoping that maybe my head is fine, what's the likely hood of this?
      0%

      I bet you will find valves bent open when you remove the head, and you can’t tell by rotating the cams.

      mine failed at idle and had 9 bent valves.

    3. #23
      What's wrong with my car?
      Join Date
      May 2021
      Location
      Utah
      Posts
      13
      Garage empty: add car
      Thanks
      1
      Thanked 0 Times in 0 Posts
      so took head to a local machine shop and sure enough found 4 bent valves..
      going to cost $375 to recondition the head...
      now i just hope i can figure out how to put it back together

    4. #24
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      552
      Thanks
      1
      Thanked 55 Times in 51 Posts
      Take your time, it’ll be fine.

    5. #25
      What's wrong with my car?
      Join Date
      May 2021
      Location
      Utah
      Posts
      13
      Garage empty: add car
      Thanks
      1
      Thanked 0 Times in 0 Posts
      Just a quick additional update here. I just picked up the head from the machine shop that I took it to and good news bad news good news is there was actually no band valves so the head was perfectly fine but sadly that's also the bad news because that means I did all this work for pretty much nothing at it cost me $500 versus an $80 belt

    6. #26
      What's wrong with my car?
      Join Date
      May 2021
      Location
      Utah
      Posts
      13
      Garage empty: add car
      Thanks
      1
      Thanked 0 Times in 0 Posts
      So cams were removed/replaced by the machine shop now i need to realign/time them.. anyone have notes for doing this on an LXV motor?
      Last edited by Offroadr; 05-17-2021 at 03:22 AM.

    7. #27
      LXV-SCOOTADRIVE, ON! 2010AveoLT's Avatar
      Join Date
      Jan 2012
      Location
      Dickson, TN
      Posts
      896
      Thanks
      119
      Thanked 82 Times in 69 Posts
      Quote Originally Posted by Offroadr View Post
      So cams were removed/replaced by the machine shop now i need to realign/time them.. anyone have notes for doing this on an LXV motor?
      Did they remove the sprockets from the camshafts? If they didn’t, then it’s just a matter of lining up the timing dots on the sprockets and locking both the sprockets and the cams themselves. (When I replaced my timing belt, I ordered a complete locking tool kit to ensure that my engine stayed in time, the tool kit I used was a German BGS kit, part number 8697) if they did remove the sprockets, the picture in my factory service manual shows the sprocket drive slots on the camshaft in a horizontal position.


      Sent from my iPhone using Tapatalk

    8. #28
      What's wrong with my car?
      Join Date
      Feb 2021
      Location
      Pennsylvania
      Posts
      1
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      My 2008 Aveo(low miles) would start all of the time, then most of the time, then some of the time, then not at all, no codes, would turn over fine. A buddy of mine who is a mechanic told me to try the Cam shaft sensor. I got one online for like $11. It was a quick 20 minute fix. Just one bolt below the oil filter. Fired right up. No issues since; changed it about 3 months ago. Hopefully this helps.

    9. #29
      Should I keep it?
      Join Date
      Jun 2017
      Location
      ks
      Posts
      54
      Thanks
      8
      Thanked 0 Times in 0 Posts
      air pressure test wudda confirmed bent valves or not, without pulling head, just guessing here, water pump bearing failure culprit , timing locking tool, crank mark 6:00....cam marks half tooth off up/down between both pulleysName:  20201225_224551.jpg
Views: 284
Size:  267.0 KBsearch tool this site , full gasket set cheaper than buying those needed separately , check coolant for oil contamination , if so, not from head gasket, oil cooler aka oil filter housing, prone to oring failure at 70k miles, good time to replace oring, thermostat and housing replace if plastic versions, check ALL coolant hoses as they are NOT oil resistant , epic blowout if ignored

    10. #30
      Should I keep it?
      Join Date
      Jun 2017
      Location
      ks
      Posts
      54
      Thanks
      8
      Thanked 0 Times in 0 Posts
      Name:  20201226_000746.jpg
Views: 343
Size:  291.4 KBName:  IMG_20180303_172624737.jpg
Views: 282
Size:  296.2 KB oil cooler




      Last edited by viciousvīc; 07-01-2021 at 02:19 AM. Reason: text added

    Page 3 of 4 FirstFirst 1234 LastLast

    Similar Threads

    1. Car starts, dies, the cant start for 30 secs. Start, die, start, die.
      By theCurrahee in forum Troubleshooting and Maintenance
      Replies: 8
      Last Post: 07-01-2021, 02:51 AM
    2. 2004 Aveo won't start
      By billetpete in forum Troubleshooting and Maintenance
      Replies: 14
      Last Post: 03-06-2020, 04:54 AM
    3. Help! Clutch and brake won't depress car won't start
      By Shrimmm1 in forum Introductions
      Replies: 2
      Last Post: 03-01-2015, 07:31 PM
    4. 2004 aveo won't start
      By nightmare in forum Engine & Drivetrain
      Replies: 12
      Last Post: 04-22-2014, 04:47 PM
    5. 2004 Aveo Won't Start
      By kclilkas in forum Troubleshooting and Maintenance
      Replies: 0
      Last Post: 07-01-2012, 09:14 PM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •