•  
    Results 1 to 8 of 8

    Thread: 2009 Aveo OBD I/M test

    1. #1
      What's wrong with my car?
      Join Date
      Sep 2019
      Location
      Hemet, CA
      Posts
      14
      Thanks
      0
      Thanked 0 Times in 0 Posts

      2009 Aveo OBD I/M test

      Was scanning engine for any codes and came across the I/M test which shows that the EVAP as inc. is this normal? If not what could I do to troubleshoot the issue as to why the test is inc.



    2. #2
      I'll keep it and add a turbo
      Join Date
      Apr 2017
      Location
      Toronto
      Posts
      104
      Garage empty: add car
      Thanks
      0
      Thanked 20 Times in 17 Posts
      Quote Originally Posted by Mberry View Post
      Was scanning engine for any codes and came across the I/M test which shows that the EVAP as inc. is this normal? If not what could I do to troubleshoot the issue as to why the test is inc.

      I also have a 2009. If i recall correctly, anytime you clear a Trouble Code, or disconnect the battery, all the I/M monitors will be set as incomplete, and they will need to run again, before they are given a okay status on the scan tool.

      EVAP is almost always the last I/M monitor to run and clear. Sometimes it can take 10 or more full drive cycles before EVAP runs. Assuming there are no emission problems, your situation sounds normal to me. It just takes time for it to run. When it eventually runs, it will either clear that monitor, or trip a new EVAP-related Trouble Code. Besides several other criteria, i believe your full level must be 3/4 or less in order for EVAP to even think about running.

      That's my 2 cents.

      Deano

    3. #3
      What's wrong with my car?
      Join Date
      Sep 2019
      Location
      Hemet, CA
      Posts
      14
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Thx I’m gonna watch it need to get a smog check done and I’m concerned that this will show on the test as an inc!

    4. #4
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      552
      Thanks
      1
      Thanked 55 Times in 51 Posts
      If the fuel tank is over half full, the computer won’t run the test. Let the tank get down to 1/4 tank and take it for a good ride. The test will run.

    5. #5
      What's wrong with my car?
      Join Date
      Sep 2019
      Location
      Hemet, CA
      Posts
      14
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Thx I’ll try that.

    6. #6
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      552
      Thanks
      1
      Thanked 55 Times in 51 Posts
      If the code pops up and the check engine light come on....there may be a work around for you. Check with the state dmv rules, most states will allow one IM monitor to be incomplete, so long as the rest passed. To do this you will have to clear the codes, drive it with no less than 3/4 tank of gas, until the rest of the tests pass, and keep the tank level higher than 3/4 tank all the time until after you’re state test.

    7. #7
      What's wrong with my car?
      Join Date
      Sep 2019
      Location
      Hemet, CA
      Posts
      14
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Sounds good thx

    8. #8
      What's wrong with my car?
      Join Date
      Apr 2015
      Location
      Davenport
      Posts
      24
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Quote Originally Posted by Mberry View Post
      Sounds good thx

      The Evap is for the gas tank fumes to be trapped inside the gas tank and be absorbed by the charcoal canister. What is supposed to happen is your filler neck where the gas cap is supposed to be sealed. A bad gas cap will pop up a leak code. Try replacing the gas cap first if the gas cap seal is stiff it should be pliable or sorta soft. If you had a smoke machine you can go right to the intake part of the engine where the purge solenoid is to put smoke into the evap lines to check for leaks. Sometimes a bad rubber hose that is dry rotted will allow a leak to happen anywhere on the system. I seen the evap and vent solenoids go out or barely work. Or a bad tank pressure sensor is not reading. The purge and vent solenoids will be near the charcoal canister and one up by the engine on the intake to purge the fumes.

      What is the code your getting when the check engine light comes on?





    Similar Threads

    1. Chevy Engine Codes (OBD-II scan)
      By tidus10 in forum Engine & Drivetrain
      Replies: 19
      Last Post: 02-21-2020, 05:21 AM
    2. Aveo 2011 OBD code P0340 Camshaft position sensor Anyone had this?
      By Mikero in forum Troubleshooting and Maintenance
      Replies: 2
      Last Post: 03-17-2018, 12:28 AM
    3. '10 Aveo keeps blowing OBD fuse
      By embea93 in forum Troubleshooting and Maintenance
      Replies: 1
      Last Post: 04-08-2016, 11:20 PM
    4. Replies: 5
      Last Post: 03-16-2015, 06:46 PM
    5. OBD 2's
      By Jet321 in forum General Discussion
      Replies: 6
      Last Post: 07-26-2014, 01:47 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •